Installing the Sandbox component

This section provides step-by-step instructions on installing the Sandbox component.

To begin the installation of the Sandbox component:

1. Run the disk image containing the Sandbox component.

   The Setup Wizard starts.

2. Click Ok.

Step 1. Viewing the End User License Agreement and Privacy Policy

To continue installation, please read the End User License Agreement (EULA) and accept its terms. Installation will not continue until you accept the terms of the End User License Agreement.

You also need to read the Privacy Policy and accept its terms.

To accept the terms of the End User License Agreement and Privacy Policy:

1. Select the language for viewing the End User License Agreement and Privacy Policy in the list.

   For example, if you want to view the End User License Agreement and Privacy Policy in English, select English and press ENTER.

   This opens a window showing the End User License Agreement text.

2. Please read the End User License Agreement.
3. If you accept the terms of the End User License Agreement, click I accept.

   This opens a window displaying the text of the Privacy Policy.

4. Please carefully read the Privacy Policy.
5. If you accept the terms of the Privacy Policy, click I accept.

The Setup Wizard proceeds to the next step.

Step 2. Selecting a disk for installing the Sandbox component

Select a physical disk for installing the Sandbox component.

To select a disk for installing the Sandbox component:

1. In the Select device window, in the list of disks, select the disk on which you want to install the Sandbox component and press ENTER.

   If the disk is not empty, a window is displayed asking you to confirm that you want to format the disk and install the program.

2. Click Install.

   The archive with the installation files will be unpacked to the disk. The server is restarted.

The Setup Wizard proceeds to the next step.

Step 3. Assigning the host name

Assign a server host name to be used by DNS servers.

To assign the host name for a server:

1. Enter the full domain name of the server into the Hostname field.

   Specify the server name in FQDN format (for example: host.domain.com or host.domain.subdomain.com).

2. Click Ok.

The Setup Wizard proceeds to the next step.

Step 4. Selecting the controlling network interface in the list

To ensure proper functioning of the Sandbox component, you must connect at least two network cards and configure the following network Interfaces:

• Management network interface. This interface is intended for providing access to the server with the Sandbox component via the SSH protocol, and the server with the Sandbox component will use this interface to receive objects from the server with the Central Node component.
• Network interface used for Internet access of processed objects. Objects that are processed by the Sandbox component can use this interface to attempt activities on the Internet, and the Sandbox component can analyze their behavior. If you block Internet access, the Sandbox component cannot analyze the behavior of objects on the Internet, and will therefore only analyze the behavior of objects without Internet access.

  The network interface used for Internet access of processed objects must be isolated from the local network of your organization.

Select the network interface that you want to use as the controlling interface.

To select the management network interface:

1. In the list of network interfaces, select the network interface that you want to use as the controlling interface.
2. Press ENTER.

The Setup Wizard proceeds to the next step.

Step 5. Assigning the address and network mask of the controlling interface

To assign the IP address and network mask of the management network interface:

1. In the Address field, enter the IP address that you want to assign to this network interface.
2. In the Netmask field, enter the network mask in which you want to use this network interface.
3. Click Ok.

The Setup Wizard proceeds to the next step.

Step 6. Adding DNS server addresses

To add DNS server addresses:

1. In the DNS servers window, select New and press ENTER.

   This opens the DNS server address entry window.

2. In the DNS server text box, enter the IP address of the primary DNS server in IPv4 format.
3. Click Ok.

   The DNS server address entry window is closed.

4. If you want to add the IP address of an additional DNS server, repeat the steps in the DNS servers window.
5. When you are done adding DNS servers, in the DNS servers window, select Continue and press ENTER.

The Setup Wizard proceeds to the next step.

Step 7. Configuring a static network route

To configure a static network route:

1. In the IPv4 Routes window, select New and press ENTER.

   This opens the IPv4 Static Route window.

2. In the Address/Mask field, enter the IP address and mask of the subnet for which you want to configure the network route.
3. If you want to use the default network route, enter 0.0.0.0/0.
4. In the Gateway field, enter the IP address of the gateway.
5. Click Ok.
6. If you want to add other network routes, repeat the steps in the IPv4 Static Route window.
7. If you are done adding network routes, click Continue.

The Setup Wizard proceeds to the next step.

Step 8. Configuring the minimum password length for the Sandbox administrator password

To set the minimum length of the administrator password for the Sandbox component:

1. In the Minimal length, enter the length in characters. Passwords 12 or more characters long are recommended.
2. Click Ok.

The Setup Wizard proceeds to the next step.

Step 9. Creating the Sandbox administrator account

Create an administrator account for working in the Sandbox web interface in the administrator menu and in the management console of the server with the Sandbox component.

To create a Sandbox administrator account:

1. In the Username field, enter the name of the administrator account. The 'admin' account is used by default.
2. In the password field, enter the password for the administrator account.

   The password must satisfy the following requirements:

   • Must contain at least 8 characters.
   • Must contain at least three types of characters:
     • Uppercase character (A-Z).
     • Lowercase character (a-z).
     • Number.
     • Special character.
   • Must not be the same as the user name.
3. Enter the password again in the Confirm password field.
4. Click Ok.

   This opens a window with the IP address of the Sandbox server. You can enter this address in your web browser to open the Sandbox web interface. To log in, use the Sandbox administrator account that you have created.

   The Sandbox server will restart.

Proceed to configuration of the Sandbox component through the web interface.